HelpCenter

Explore
MM6 - Setup and Installation Guide
Updated

Purpose

The MM6 device is a solution ideal for high-touch, high-traffic locations. This article acts as an on-site installation guide to the MM6 device.

This device supports an Expansion Unit (XP6), which contains peripherals such as a Vertical Up-Stacker and a Receipt Printer. Learn how to install the XP6 by reading the article MM6 XP Unit - Setup and Installation Guide.

Additional peripherals are also available for the MM6. Please see the MM6 - Hardware Guide and the MM6 Spec Sheet for more information. 

 

The MM6 Kiosk with a black screen

 

Software

There are a few types of MM6 devices, and each one has a different type of software. 

  • The MM6-RT uses ReadyTouch software
  • The MM6-CK uses CK Software
  • The MM6 Markets uses V5 Software

 

Setup Requirements

An MM6/ MM6+ setup will require:

  • One 120VAC 3-prong grounded outlet (15 amp service)
  • One RJ45 wired Ethernet jack

 

MM6 Specifications

  • 13.75" wide x 29.75” high x 15.5” deep
  • 51 lbs (23 kg), 59 lbs/ 28 kg boxed

 

Tools Required for Installation

  • 8th-inch hex wrench
  • 7/16th combination wrench
  • 3/8" drill bit and drill, if installing via the provided carriage bolts
  • Drill driver and bit, if installing via wood screws
  • electrical tape

 

MM6 Installation

The MM6 itself is a plug-and-play device. It is staged and assembled prior to shipment.

  1. Carefully unpack the MM6 kiosk. Be sure not to lose any mounting hardware or accessories which are included in the packaging box. Please contact 365 immediately if there is any damage caused by shipping.

    mceclip0.png
  2. Place the Drill Template (included in packaging and in the attachments of this article) on the countertop in the desired location and secure it with tape. Use a 3/8" drill bit to drill holes in the two marked locations on the guide.

  3. Place the unit in the desired location on the counter, lining up the drill holes with the holes in the device. Insert the supplied carriage bolts through the square holes and secure them from the underside of the countertop with the washers and nuts.
    • If using the supplied wood screws, place the unit in the desired location and drive the screws through the base holes using a drill driver.

  4. Connect the MM6 to the 120VAC 3-prong grounded outlet. Press and hold the Power button located at the back of the kiosk, holding until it beeps. The MM6 will then boot up and automatically start the POS (Point of Sale) software.


    To properly shut down the Kiosk when needed:

    • Open the kiosk and power down the PC by pressing its power button.

    • Once the PC is off, turn off the Kiosk by holding the Power button located in the back of the kiosk (the UPS) until you hear a long beep and then two short beeps.

  5. Once the unit is powered up, the operator should verify network connectivity and set up the router by connecting an operator-provided network cable from the MM6's LAN port to your local connection jack. Power for the router is supplied separately from the rest of the device. For more information on this process, see the Validating Network Status on ADM section of our Network Connectivity Verification article. 

  6. Locate and write down the serial number of the MM6, located on the side of the kiosk. Use this number when contacting 365Support at (888) 365-6282 to complete remote configuration. 

 

XP Unit Installation 

This device supports an Expansion Unit (XP6). This expansion unit is an optional component that connects to the left side of the countertop kiosk. It contains peripherals such as a Vertical Up-Stacker and a Receipt Printer. When the Expansion Unit is combined with the MM5, these devices are called the MM6+.

Learn how to install the XP6 by reading the article MM6 XP Unit - Setup and Installation Guide.